2017 Fox 32 Float 140 Rl Manual

Among Singletracks readers, the Reba 29 RLT version is the most popular, but keep in mind this fork is offered OEM only. If you’re looking for an aftermarket upgrade, check out the Reba RL. Bonus: the Boost version of the Reba RL 29 is compatible with 3-inch, 27.5+ tires. Easily find the correct oil volume specifications for your Fox bicycle suspension forks. 32 FLOATの最大空気圧は 140psi/9.6bar. 34 FLOATとRHYTHMの最大空気圧は 120psi/8.3bar. 32/34 TALAS の最大空気圧は 200psi/13.8barらしい。. Freshen up your Fox shock. Let the air out of the fork. FOX Fox Base Valve RLC Vanilla-Float 76, 05 $ FOX Fox Topcap 32 140 RL 92, 43 $ FOX Fox U-Cup Scraper Air Piston Seals 10, 53 $ FOX Fox Damper Rebuild Kit Float. Page 16: F Series/Fx. I was running a F29 RLC on the Dillinger, both of which.

Fox 32 Float Rl
Fox 32 Rl
2017 Fox 36 Rc2
Fox Float 32 Rl Rebuild
2017 Fox 32 Float 140 Rl Manual Transmission

You are here: Forks > 32 mm > FLOAT > FLOAT FIT RL

Fox 32 Float Rl

travel	140 RL: 5.5 in./140 mm 150 RL: 5.9 in./150 mm
features/adjustments	lever-actuated lockout, air spring pressure, rebound
spring/damper type	air/FIT RL
intended use	all-mountain, cross-country

Installing Your Fork

Be sure your fork is properly installed before proceeding. If your fork came pre-installed on your bicycle, continue to the next section.

Before You Ride

Check that quick-release levers are properly adjusted and tightened.
Clean the outside of your fork with only mild soap and water, and wipe dry with a soft dry rag.
Note:Do not use any solvents or de-greasers, as these products can cause serious damage to paint and anodized parts (upper tubes, knobs, steerers).
Do not spray water directly on the seal/upper tube junction. Do not use a high pressure washer on your fork.
Inspect the entire exterior of your fork. The fork should not be used if any of the exterior parts appear to be damaged. Contact your local dealer or FOX Racing Shox for further inspection and repair.
Check your headset adjustment. If loose, adjust it accordingly to your bicycle manufacturer's recommendations.
Check that all brake cables or hoses are properly fastened.
Test the proper operation of your front and rear brakes on level ground.

Setting Sag

You can also view a Flash video on Setting Sag.

To get the best performance from your fork, it is necessary to set and adjust sag. Generally, sag should be set to 15 – 25% of total fork travel.

Unscrew the blue aircap on top of the left fork leg to expose the Schrader valve.
Attach a FOX Racing Shox High Pressure Pump to the Schrader valve.
Pump your fork to the appropriate setting from the Suggested Air Spring Pressure Settings table below, then remove the pump.
Unless your fork already has a sag setting o-ring on an upper tube, install a zip tie to an upper tube. Slide the o-ring or the zip tie down against the scraper lip of the fork dust seal.
Make sure your fork lockout is not engaged.
Dressed to ride, position your bike next to a wall or table to support yourself. Without bouncing, mount your bicycle. Assume a normal riding position for at least 30 seconds, allowing the suspension to fully settle.
Dismount your bike without bouncing downward, without further moving the o-ring or zip tie. Measure the distance between the seal and the zip tie. This measurement is your sag value.
Compare your actual sag value to your target sag value in the Sag Setup table below.
If your sag measurement value is less than the Sag Setup table value, screw on the pump ﬁtting, note the current air pressure setting and depress the black bleed-valve to reduce the gauge pressure by 5 psi. Measure sag again and repeat this adjustment, if necessary.
If your sag measurement value is greater than the Sag Setup table value, screw on the pump ﬁtting, note the current air pressure setting and pump to increase the gauge pressure by 5 psi. Measure sag again and repeat this adjustment if necessary.

Screw the blue aircap back on, and go ride.

Rider Weight lbs.	Suggested Air Spring Pressure Settings PSI
Rider Weight lbs.	140 mm	150 mm
≤125	45	40
125 - 135	50	45
135 - 145	55	50
145 - 155	65	60
155 - 170	70	65
170 - 185	75	70
185 - 200	80	80
200 - 215	90	90
215 - 230	100	100
230 - ≥250	110	110

Sag Setup
Travel	XC/Race FIRM	All-Mountain PLUSH
140 mm (5.50')	21 mm (0.81')	35 mm (1.38')
150 mm (5.90')	23 mm (0.91')	38 mm (1.50')

Sag Troubleshooting
Symptom	Remedy
Too much sag	(+) air pressure in 5 psi increments
Too little sag	(-) air pressure in 5 psi increments
Excessive bottoming	(+) air pressure in 5 psi increments
Harsh ride; full travel not utilized	(-) air pressure in 5 psi increments

Adjusting Rebound

The rebound adjuster knob is located at the bottom of the right fork leg. This knob has 18 clicks of potential adjustment range.

Rebound controls the rate of speed at which the fork extends after compressing. Turning the knob clockwise slows down rebound; turning the knob counter-clockwise speeds up rebound. As a starting point, turn the rebound adjuster knob all the way clockwise (full in) until it stops, then turn counter-clockwise (out) 12 clicks.

Knob Setting (clicks out from full in)	Setting Description	Tuning Tips	Setup Tips
1	Slow Rebound	Too slow and your fork will pack down and ride harshly.	If you increase your spring rate or air pressure, you will need to slow down your rebound
12 (Factory setting)	Average Rebound
18	Fast Rebound	Too fast and you will experience poor traction and wheel hop.	If you decrease your spring rate or air pressure, you will need to speed up your rebound setting.

Locking Out the Fork

The blue compression lockout lever, located on the right-side top cap, allows you to close the compression damping circuit in the fork. This keeps the fork at the top of its travel, making it harder to compress.

Rotate the lever fully clockwise to lock out the fork. This position is useful in climbing and sprinting situations, but will sag with the rider’s weight. The fork will 'blowoff' in the event that a big hit is encountered with the fork locked out.

Fox 32 Rl

To unlock the fork, simply rotate the lever fully counter-clockwise.

2017 Fox 36 Rc2

Note:The fork may cycle a couple of times after enabling lockout. Once complete lockout is achieved, the fork may continue to move 3 - 5 mm. This is normal and does not affect performance.

2017 fox 32 float 140 rl manual for sale